ZedsDead
04-08-2008, 11:47 AM
I have found some information (here) about ANC but I am wondering if anyone has actually disabled the system yet?
I am having the exact same issues and the system will be unusable until I fix this problem: Here are the specs
I completed Phase 1 of my install this past weekend, now I am "debugging" the system.
Here are the specs of my system:
2008 Accord LX-S Coupe Factory Head Unit (6-disk)
---------------------------------------------------
JL Audio Cleansweep (CL-SSI Not needed BTW!!)
Xtatic BatCap 400
Alpine MRP F600 4ch Amp
Eclipse XA1200 mono amp
Boston Acoustic Pro60 (F)
Boston Acoustic SL60 (R)
Specs of Install:
Removed all seats, door panels, kick and rail modings, rear decklid, center console, and bezel before starting:
Under upper passanger side floorwell, cut out some padding to mount CleanSweep Unit and wired up.
Removed rear seat covering and built frame to mount amps and battery cap. Ran power wires along driver side and speaker wires along passanger side.
Mounted Pro60s up front as seperates. Dynamat front of door area, cut foam block to mount crossovers and glued to insde door panel. (Set both tweeters to -4db)
Dropped in SL60s as coaxial.
Calibrated Cleansweep at vol:20 (at 30 I had issues with distortion).
Whats left?
Figuring out how to disable ANC as it is going to blow up my sub. Any hints would be greatly appreciated.
Installing EQ, Sub Level and Sound Imaging/Staging processor. Probably RF 3Sixty but Im looking in to what Audio Control Offers.
I didn't think about taking pics during install but I ran downstairs and took these today (sorry about the load time for this page of the thread!).
http://www.gamenetusa.com/stereo/st1.jpg
http://www.gamenetusa.com/stereo/st2.jpg
http://www.gamenetusa.com/stereo/st3.jpg
http://www.gamenetusa.com/stereo/st4.jpg
http://www.gamenetusa.com/stereo/st5.jpg
http://www.gamenetusa.com/stereo/st6.jpg
http://www.gamenetusa.com/stereo/st7.jpg
I am having the exact same issues and the system will be unusable until I fix this problem: Here are the specs
I completed Phase 1 of my install this past weekend, now I am "debugging" the system.
Here are the specs of my system:
2008 Accord LX-S Coupe Factory Head Unit (6-disk)
---------------------------------------------------
JL Audio Cleansweep (CL-SSI Not needed BTW!!)
Xtatic BatCap 400
Alpine MRP F600 4ch Amp
Eclipse XA1200 mono amp
Boston Acoustic Pro60 (F)
Boston Acoustic SL60 (R)
Specs of Install:
Removed all seats, door panels, kick and rail modings, rear decklid, center console, and bezel before starting:
Under upper passanger side floorwell, cut out some padding to mount CleanSweep Unit and wired up.
Removed rear seat covering and built frame to mount amps and battery cap. Ran power wires along driver side and speaker wires along passanger side.
Mounted Pro60s up front as seperates. Dynamat front of door area, cut foam block to mount crossovers and glued to insde door panel. (Set both tweeters to -4db)
Dropped in SL60s as coaxial.
Calibrated Cleansweep at vol:20 (at 30 I had issues with distortion).
Whats left?
Figuring out how to disable ANC as it is going to blow up my sub. Any hints would be greatly appreciated.
Installing EQ, Sub Level and Sound Imaging/Staging processor. Probably RF 3Sixty but Im looking in to what Audio Control Offers.
I didn't think about taking pics during install but I ran downstairs and took these today (sorry about the load time for this page of the thread!).
http://www.gamenetusa.com/stereo/st1.jpg
http://www.gamenetusa.com/stereo/st2.jpg
http://www.gamenetusa.com/stereo/st3.jpg
http://www.gamenetusa.com/stereo/st4.jpg
http://www.gamenetusa.com/stereo/st5.jpg
http://www.gamenetusa.com/stereo/st6.jpg
http://www.gamenetusa.com/stereo/st7.jpg