okay so i was driving the other day and all of the sudden it seemed as though it had popped out of 1st gear. as i put it back in to 1st it still wouldnt move. nor in any other gear. i got out and looked and my cv axle broke. no biggy i knew it was bad so i replaced it today.... BUT when i put it into first or any other gear it still doesnt go anywhere. so i get out and look again with it in reverse (keep in mind it still doesnt move) and the car running and it looks as though that the axle isnt in all the way and it just kinda jumbles around rattling kinda inside the transmission where the transmission end of the axle goes into.

could somehow the splines INSIDE the transmission be stripped? any ideas or ANYTHING is GREATLY appreciated becasue i need this car up and going by this friday. the day after tommorrrow!
thanks a ton!!

okay so i was driving the other day and all of the sudden it seemed as though it had popped out of 1st gear. as i put it back in to 1st it still wouldnt move. nor in any other gear. i got out and looked and my cv axle broke. no biggy i knew it was bad so i replaced it today.... BUT when i put it into first or any other gear it still doesnt go anywhere. so i get out and look again with it in reverse (keep in mind it still doesnt move) and the car running and it looks as though that the axle isnt in all the way and it just kinda jumbles around rattling kinda inside the transmission where the transmission end of the axle goes into.

could somehow the splines INSIDE the transmission be stripped? any ideas or ANYTHING is GREATLY appreciated becasue i need this car up and going by this friday. the day after tommorrrow!
thanks a ton!!

okay so i was driving the other day and all of the sudden it seemed as though it had popped out of 1st gear. as i put it back in to 1st it still wouldnt move. nor in any other gear. i got out and looked and my cv axle broke. no biggy i knew it was bad so i replaced it today.... BUT when i put it into first or any other gear it still doesnt go anywhere. so i get out and look again with it in reverse (keep in mind it still doesnt move) and the car running and it looks as though that the axle isnt in all the way and it just kinda jumbles around rattling kinda inside the transmission where the transmission end of the axle goes into.

could somehow the splines INSIDE the transmission be stripped? any ideas or ANYTHING is GREATLY appreciated becasue i need this car up and going by this friday. the day after tommorrrow!
thanks a ton!!
Short answer is yes. You could have stripped them. Did you not look at them b4 swapping the new axle?

no i never thought i wouldve stripped them. fml.
how much ya think this is gonna run me $ wise?

It may not be that. If i were u since you have time constrants. take it somewhere to be looked at.

im kinda low on the $ haha. so iguess ill be taking it apart again tommorow and try and look at it. how do i tell if they are stripped? cause i dont think i can really see in there?

If u cant afford to take it in, what does taking it back off help if you cant see that you need to see or how will u repair it if the worst is whats wrong? lol.

start saving? lol you got any ideas?

thought u needed to be rolling by friday? no i have no ideas. well yess one. pray!!!

ahaha yea.. i do. thats a BIG problem haha damn.. fml. got any idea how much this could cost? lol

Look here.

http://www.driveaccord.net/forums/showthread.php?t=35884


:paranoid:

Threads merged.

OP, please do not double post the same topic.

I think he ment to put in early models sinces hes a 5th gen. Might wanna move it to 5th gen where his car should be.

Moved to Early Generations.

Or you can always take it back out and get a flash light and look inside the transaxle hole to see what condition the splines are in.

sorry about that guys. figured it out. splines just werent in there all the way. had to pound it in with a rather large hammer. and i just got back yesterday from an 800 miles road trip with no problems what so ever.
thanks for the help