Drive Accord Honda Forums banner
Cancel

Media added by sfm6s524

Navigation

Browse albums
Of course the Garmin blocks the tweeters on the EX sail panels, but for me that's okay for now.

Of course the Garmin blocks the tweeters on the EX sail panels, but for me that's okay for now.

  • 0
  • 0
Mounted crossover to flat bar mounted to door with sheet metal screws. Drilled 3/16" hole through the two mounting holes in the crossover, thro

Mounted crossover to flat bar mounted to door with sheet metal screws. Drilled 3/16" hole through the two mounting holes in the crossover, thro

  • 0
  • 0
Trimmed all outside tabs from provided Polk mounts and used it as a 1/4" spacer.

Trimmed all outside tabs from provided Polk mounts and used it as a 1/4" spacer.

  • 0
  • 0
Sheet metal screws hold fuse link to battery hold down.

Sheet metal screws hold fuse link to battery hold down.

  • 0
  • 0
I trimmed circuit board carefully to narrow width so it would fit through opening.

I trimmed circuit board carefully to narrow width so it would fit through opening.

  • 0
  • 0
Sub volume button mounted through blank cover.

Sub volume button mounted through blank cover.

  • 0
  • 1
Brackets made from 1/8" x 1" steel bar to mount closer to rear seat.

Brackets made from 1/8" x 1" steel bar to mount closer to rear seat.

  • 0
  • 0
About 29-30 inches between trunk rear and sub.

About 29-30 inches between trunk rear and sub.

  • 0
  • 1
HFL Update Results

HFL Update Results

  • 0
  • 0
Done!

Done!

  • 0
  • 0
Finished look. Not perfect, but if you didn't know they were there, hardly noticeable.

Finished look. Not perfect, but if you didn't know they were there, hardly noticeable.

  • 0
  • 0
Just before removing the tape.

Just before removing the tape.

  • 0
  • 0
Using the Honda touch up paint applied 3 coats, allowing at least 30 minutes between coats.

Using the Honda touch up paint applied 3 coats, allowing at least 30 minutes between coats.

  • 0
  • 0
After second application of epoxy and before paint.

After second application of epoxy and before paint.

  • 0
  • 0
I used a 1/4" punch to create a hole matching the size of the area to be painted.

I used a 1/4" punch to create a hole matching the size of the area to be painted.

  • 0
  • 0
While dry remove the tape and carefully clean up the area around the hole to remove all excess epoxy.

While dry remove the tape and carefully clean up the area around the hole to remove all excess epoxy.

  • 0
  • 0
Used a toothpick to get the material deep into the hole and left enough to be able to swipe down towards the tape to level.

Used a toothpick to get the material deep into the hole and left enough to be able to swipe down towards the tape to level.

  • 0
  • 0
Bumper repair epoxy kit purchased at local auto parts store.

Bumper repair epoxy kit purchased at local auto parts store.

  • 0
  • 0
Other options I considered, but didn't do.

Other options I considered, but didn't do.

  • 0
  • 0
A small fine stone ball was used to further work the area to below surface.

A small fine stone ball was used to further work the area to below surface.

  • 0
  • 0
Since the screws tend to create a raised mound of material, the area was first leveled with a sharp razor.

Since the screws tend to create a raised mound of material, the area was first leveled with a sharp razor.

  • 0
  • 0
Here are the 2 holes that need filling since adding the new license plate bracket.

Here are the 2 holes that need filling since adding the new license plate bracket.

  • 0
  • 0
USB Adapter

USB Adapter

  • 0
  • 0
Groit Fluid Extractor http://www.griotsgarage.com/product/multi+fluid+extractor.do

Groit Fluid Extractor http://www.griotsgarage.com/product/multi+fluid+extractor.do

  • 0
  • 0
Ran cable behind door trim.

Ran cable behind door trim.

  • 0
  • 0
Top