Drive Accord Honda Forums banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-12 of 12 Results
  1. The 8th Generation
    I’ve just put the cylinder heads back into the car and now I need to put everything in time. I know that I want the valves for cylinder #1 at top dead center for the start of a compression stroke, but what postion do I want the other camshaft in?
  2. Performance
    Hello folks: I drive a 2010 Honda Accord, EX trim, 4cyl. I was wondering if this simple pressure relief valve from Heidts: https://www.heidts.com/inst/in-053.pdf could be installed in-line with my steering pump hoses? Just wanted to firm up the steering feel a bit. Eighty-plus views and no...
  3. DriveAccord Classifieds
    I am looking to buy a proportioning brake valve from or out of a 1992-1996 Prelude S. It has to be from an "S" trim as it has to be non-ABS. Part Number is 46210-SS0-003 Looking to use it to complete my rear disc conversion so it must be in working order. Thanks! Received one from a member of...
  4. The 10th Generation
    Has anyone installed a catch can on their '18 yet? If so, curious which one you used and how you mounted it. Hoping Mishimoto will come out with one for ours like they did for the Civic.
  5. The 7th Generation
    Hi guys, this thread topic probably already exists somewhere but i couldn't seam to find it anywhere so here i am asking. I bent at least one of my valves when i miss shifted form 3rd down into 2nd. I was wondering if it is possible to take off the cylinder heads without taking out the engine?
  6. The 7th Generation
    Hey All - So in my continuing quest...my new to me 06 Accord with around 240K miles is getting some much needed maintenance. I don't believe any real maintenance was performed from what I can tell by the prior owner. While I'm not 100% sure, it's likely that these plugs are the...
  7. The 8th Generation
    Actual mileage: 150KKm, no accident, always on time oil change and no liquid shortage or overheating. Thing happened on highway driving at 120Km/hr speed, ECL on and shaking, then no longer able to drive above 3,000rpm and 60Km/hr. Recent service history: changed 5W20 highmileage at Jiffy...
  8. The Early Generations
    I just replaced all gaskets, including the o-rings under the rocker assembly, but I am still getting an oil leak outside of the valve cover and near the intake side of the number one spark plug and (see below). Any ideas?
  9. Problems & Solutions
    hi everyone, 2000 accord 2.3l, 185x so i know how to do valve adjustments. but on my car, on certain valves (cyl 1 and 2, primary rocker arms), i cannot get the valve adjustments to stay put. for e.g. i adjust it to a certain spec, tighten it and when i rotate the engine and check it again...
  10. The 7th Generation
    Does anyone have the valve lash specifications for a 2006 Accord EX 4 cylinder? There is not a sticker under my hood showing the valve lash spec so when I set the lash last week I used .009" for the intake and .011" for the exhaust. Since setting the lash the valve seating sounds louder, the...
  11. The 7th Generation
    I have a 2004 Accord v6 and the rear valve cover is leaking. I called a shop and they want $410 to do the work. That seemed really high to me so I'm going to do it myself. the service manual says that I need to remove the intake manifold. I can't find the diagram for removing the intake manifold...
  12. The 7th Generation
    Hi everyone, I have an 07 Accord Coupe 6-6 and was wondering whether the following TL "mod" applies to us as well: http://tl.acurazine.com/forums/showthread.php?t=734300 Do we have the same valve in our Accords and if yes, has anyone removed it? Thanks!
1-12 of 12 Results
Top